A dildo shaped exactly like your partner's penis or your own: that is the idea behind a penis mould. With a moulding kit you can do it in one evening in your own kitchen, without any prior experience. What matters is not skill but planning. If you know which version you want, what has to be ready and why most attempts fail, you end up holding a cast instead of a lump. You will find the right kits in our collection penis moulding kits.
DIY Dildo Penis Cloner Kit Pink
€35,99
DIY Dildo Penis Cloner Kit with Vibration Black
€34,99
DIY Dildo Tulip Pink
€35,99
Casting Kit Penis Candle Red
€35,99
Realistic Dildo Spencer Large Natural 25.5 x 6.2 cm
€36,99
Realistic Dildo Gary L with Balls Natural 23 x 4.7 cm
€34,99🧪 How a penis mould works
Every moulding kit works in two steps. First a negative mould is made: you mix moulding powder with water, the erect penis goes into the cup, and the mixture sets within a few minutes. Then you fill this mould, depending on the kit with silicone or with wax. The silicone cures over several hours. Only then do you take it out. So expect a few minutes for the impression and a long wait for the cast.
🎯 Which version suits you?
Before you order, ask yourself what you want to end up with. The kits differ mainly in what you make from the impression:
- Classic silicone dildo: the place to start, for example with the Penis Cloner Kit Pink or the DIY Dildo Tulip Pink in a bold pink.
- Cast with vibration: with the Penis Cloner Kit with Vibration Black you insert a vibrating unit into the cured silicone.
- A candle instead of a toy: the Penis Candle Moulding Kit Red is cast with wax. The result is for looking at and lighting, not for insertion – a gift with a wink.
Further versions with a suction cup, with a harness or in glowing silicone return to the collection depending on availability. The process stays the same.
📋 Preparation is everything
The powder will not wait for you. So the rule is: have everything ready before you mix. This list helps:
- 🕒 Time: a quiet evening with no deadline, the curing runs overnight.
- 💧 Cool water: the warmer the water, the faster the mixture sets. Mixed cool, you keep more leeway.
- 🚰 A stable spot: the cup must not tip over, the sink is a good place.
- ✂️ Pubic hair: trim it or apply cream beforehand, otherwise it gets stuck in the mixture.
- 👫 As a pair: one stirs, one holds – that takes a lot of the rush out of it.
⏱️ The process at a glance
Mix, insert the penis, hold still until the mixture is firm, then pull out carefully. Fill the mould and let it cure in peace. The impression fails most often because of the erection: it has to be stable and last the full time, otherwise the mould does not capture everything. That is not down to the kit but to the moment – so it pays to go into it relaxed and without pressure. We explain each step, the amounts and the timings in detail in the Cloneboy step-by-step guide.
🔍 What to expect from the result
A cast made in the kitchen is not mass production. Small bubbles and a surface that is not perfectly smooth are part of it. The shape is close to the original, but not perfect. If you take it out before the silicone is firm, you get a soft lump instead of a toy – patience is the most important step here. How industrially made toys are produced by comparison is shown in our article How are dildos made?
🧼 Care and lube for the finished cast
Wash the finished silicone cast and let it dry. With the vibration kit, remove the insert first, because it is electronic – only the silicone goes under water. A water-based lube is the right choice. Silicone lube attacks silicone and makes the surface sticky over time. You can read more about the material in our guide to silicone dildos. The candle, on the other hand, goes on a fireproof surface and should never be left burning unattended.
The vibration kit also contains an adjustable cock ring. It stays on for no more than 20 to 30 minutes at a time. If anything hurts, or the skin turns cold, numb or discoloured, take it off immediately. If you take blood thinners or have circulation problems, talk to a doctor first.
❓ Frequently asked questions
🔁 Can I use a kit more than once?
As a rule, no. Powder and casting material are portioned for one cast. If the impression fails, the moulding powder is available as a refill pack; with the vibration kit the powder already covers two impressions.
⌛ How long does a penis mould take in total?
The impression itself only takes a few minutes. Curing the silicone takes several hours, so plan for an evening plus the night.
💡 What is the most common mistake?
Water that is too warm. It shortens the setting time so much that the impression stays incomplete. Next come a fading erection and removing the cast too early.
🎁 Is a penis mould a good gift?
For couples, yes, because making the mould is already a shared experience. The only thing that matters is that both of you are up for it. If you would rather skip the crafting evening, choose a ready-made toy such as the Realistic Dildo Spencer Large or the Realistic Dildo Gary L. Our big dildo guide helps you decide which size and shape suits you.
✅ Conclusion
Making a penis mould yourself is less about craftsmanship than organisation: choose the right version, use cool water, keep everything within reach, work as a pair and give the silicone the time it needs. Then one evening turns into a toy that exists only once. And if the first attempt does not work out, that is no drama – a refill pack gives you a second chance.
🛒 Matching products in our shop
Want to browse straight away? Everything this article is about:
- Penis impression – all moulding kits for a dildo, vibrator or candle
- Realistic/Classic Dildos – ready-made realistic dildos if you would rather not cast one yourself
